[1QUICKGT]

I am keeping the 88 next to it w/o the stripes. Do not ask if it is for sale please.

89 GT with salvage title, this is the same car I hit a pole at a gas station with. Door and right quarter were damaged. That was all(first pic shows that damage) Car is no longer damaged and has been painted. That damage happend 3 years ago.

Car is also pretty light, 2780 w/o driver.

Most of you know this car as my car. I have bought another GT that will be built as my daily driver so I am letting this one go.

Here is a list of most parts that will be on the car or that are included.

Car itself
3" pin on hood
UPR Pro Kit rear suspension, dbl adj. uppers, adjustable lowers, anti roll bar,
Rear end is a built 8.8, 5 lug with drums, has moser 33 splines, moser spool, strang C-clip elims, new E-brake cables, new brakes, T/A cover,
convo pro wheels 5 lug rear, 4 lug front
NEW front tires with NO miles on them
NEW 275/50/15 ET Street Radials with a couple burnouts on them but only 15 street miles, no track time.
8 point mild steel cage
sub frame connectors
welded t-box's
spare tire well cut out with 18ga. plate welded back in it's place
16 gallon fuel cell
holley blue pump
1/2 fuel lines
holley reg. (no lines from reg. to carb)
6pc clear corner light kit
LX tail lights(not the ones in the pics)
Taylor aluminum battery box
flaming river push/pull shut off switch
wolfe fire wall
stock front suspension
Older set of TRS Corbeau seats


The car has no carpet in it, no rear seat, no center con. but I do have it,
You will need to put your motor and transmission in the car the way it is going to be sold.

As a roller with everything listed above I am asking $3800 obo

If you want a motor and transmission I can sell you those also. As for now I will NOT sell the transmission or motor until the car sells. I will make some one a deal on everything though.

motor available for $1000
85 Forged factory piston motor
new rings & bearings
Cam is a Chet Herbert mechanical -
Lobe Center line 108
Ground 4 advanced
247 and 259 @ .050
.541 and 573 lift
Stout cam
It is a Chet Hebert F5S
Harland Sharp roller rockers

Heads are 69 ford 351W ported by Ron Vesterby, nothing radical, bowl, cleanup, exhaust port opened.


Trans price $1200.
Trans available is a Redneck Performance C4, will include bell housing, B&M Shifter with transbrake button on ball, flexplate, 4400-4600 9" stall, This stall would hold on brake in my car(306) to 4500.
Transbrake valve body
Full manual shift
Reverse shift pattern
Rollerized gearset
Hardened input shaft
Reinforced forward drum
Billet servo
Deep pan
High performance frictions
Rated to 650 HP


Other parts available
650 mighty demon $400
RPM Air Gap II intake with port work $150
MSD Blaster SS coil $45
MSD Pro Billet Distributor pn8582 $200
MSD 6AL $175


If some one wants me to put the car together with all the parts listed above and make it run I will also do that. If I make it run with those parts will let the car go for $6000.

If I make it run I will also include the exhaus that is on the car right now. FMS headers, dr. gas X pipe, 3" prochambers. I will also leave my aluminum drive shaft in the car if it is sold running.

I still have the car running and driving but can have it apart in less that 24 hours of selling it. If you want me to put the motor in it I will have it ready in 2-3 days.



The pics are before the UPR uppers and lowers

[1QUICKGT]

I also have a T-5 set up I will sell with the car or installed in the car.

[1QUICKGT]

The C4 has been sold, car is available with motor and T-5 set up now.

[1QUICKGT]

All these pictures are from yesterday. It's dirty as hell from sitting outside alot.














Before the cage and antiroll bar. With the old T-5 leave on motor.

[1QUICKGT]

SOLD today as a roller