Good Deal?

SAvoltage · 06-12-2005, 01:44 PM

is this what i need
1996 V6 Mustang

here

93Stanglx · 06-12-2005, 02:09 PM

you dont have the o2 sensors?

SAvoltage · 06-12-2005, 02:10 PM

ive got flows with no cats.. check engine lights on

93Stanglx · 06-12-2005, 02:17 PM

Quote:

Originally Posted by SAvoltage

ive got flows with no cats.. check engine lights on

hmm I dont think that by not having cats will give u the check engine light..then again im not sure on 96+ stangs. im sure someone else on here should know though good luck.

BigJnSA · 06-12-2005, 05:28 PM

not having cats is exactly why you got the CEL on. i wouldnt think v6 or v8 would be different. but see if any 6ers on here know for sure.

timpryor · 06-12-2005, 05:36 PM

yes you need the MIL's but not if you put the cats back on.

ed5150 · 06-12-2005, 07:05 PM

Running without Cats right now is probably causing your car to run too Lean...so the CEL is on...once you weld in a set of cats, the CEL should turn off..... :jeff:

txlen · 06-12-2005, 08:00 PM

do you have the front O2's hooked up???...all the downstream O2's do is tell the comp if the cats are doing their job....if you have the fronts and not the rears then throw on some Sim's on the rear and reset the comp and it'll be ok...Len

keg65 · 06-12-2005, 08:00 PM

I used the MIL for a Mustang on my Focus, just one though. I was running an off road header, no cat and it worked fine. I don't see any reason why it wouldn't work for your V6, its the same idea to change the reading the computer gets from the O2 sensor.

tire · 06-30-2005, 12:05 AM

Quote:

Originally Posted by keg65

I used the MIL for a Mustang on my Focus, just one though. I was running an off road header, no cat and it worked fine. I don't see any reason why it wouldn't work for your V6, its the same idea to change the reading the computer gets from the O2 sensor.

you can try that, but they are very touchy and i wouldn't be surprised if your outcome came out differently from others. some MIL elims dont even always work... stupid computers.

06-12-2005, 01:44 PM	#1
SAvoltage Registered User Join Date: May 2005 Location: San Antonio Posts: 1,568 Trader Rating: (0)	Good Deal? is this what i need 1996 V6 Mustang here

06-12-2005, 02:09 PM	#2
93Stanglx Registered User Join Date: Jan 2005 Location: San Antonio/LA Posts: 266 Trader Rating: (0)	you dont have the o2 sensors? __________________ 1993 LX converted to GT :jeff:

06-12-2005, 07:05 PM	#7
ed5150 There's only 1 way to Rock! Join Date: Nov 2004 Location: Pearl City, Hawaii Posts: 949 Trader Rating: (0)	Running without Cats right now is probably causing your car to run too Lean...so the CEL is on...once you weld in a set of cats, the CEL should turn off..... :jeff: __________________ 1994 5.0 GT 292 RWHP 332 RWTQ

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

06-12-2005, 02:10 PM	#3
SAvoltage Registered User Join Date: May 2005 Location: San Antonio Posts: 1,568 Trader Rating: (0)	ive got flows with no cats.. check engine lights on

06-12-2005, 08:00 PM	#8
txlen Jus Workin Away !!! Join Date: Nov 2004 Location: San Antonio, Texas Posts: 1,795 Trader Rating: (2)	do you have the front O2's hooked up???...all the downstream O2's do is tell the comp if the cats are doing their job....if you have the fronts and not the rears then throw on some Sim's on the rear and reset the comp and it'll be ok...Len

06-12-2005, 08:00 PM	#9
keg65 Change always makes Sense (or Cents) Join Date: May 2005 Location: NE San Antonio Posts: 1,210 Trader Rating: (0)	I used the MIL for a Mustang on my Focus, just one though. I was running an off road header, no cat and it worked fine. I don't see any reason why it wouldn't work for your V6, its the same idea to change the reading the computer gets from the O2 sensor.