Looking for exhaust shop to install OR H in NW side.

aguilarf · 05-18-2008, 01:48 AM

Any know of a good exhaust shop on the NW side (Bandera/410, Culebra/410/1604) that would be willing to install an OR H pipe.

I hit up some of the local franchise shops and the all declined. Car is too low to do it myself, so a lift would be the easiest way. Car is not a daily driver and probaly doesn't even see 500 miles per year. Thanks for your help.

**Lethal Performance** · 05-18-2008, 02:08 AM

We could do it. If we can get lowered to the max Cobra's, Ford GT, Viper and Corvettes on the lift Im sure we can do yours. Email us at lethalperformance@yahoo.com

acrod · 05-18-2008, 09:41 AM

how low is your car?

H0SS302 · 05-18-2008, 09:44 AM

his car is pretty damn low, the front is like maybe 2inches off the ground(if that)

2k4mk1 · 05-18-2008, 10:20 AM

Midas Mienke etc will not do it as it is against the law for them to remove any emissions control items. If yopu have ramps you could use about three pcs of 2x6 stacked progressively to raise the front so it would clear the ramps and be able to get it up on them. It is a little hard to explain online but hopefully you understand what I am saying

txlen · 05-18-2008, 10:27 PM

Quote:

Originally Posted by 2k4mk1

Midas Mienke etc will not do it as it is against the law for them to remove any emissions control items. If yopu have ramps you could use about three pcs of 2x6 stacked progressively to raise the front so it would clear the ramps and be able to get it up on them. It is a little hard to explain online but hopefully you understand what I am saying

yep..i got ramps built like that..

FordGT08 · 05-19-2008, 11:37 AM

i can install for cheaper than a shot just roll the fron tires on a 2x4 and then run my low profile jack under it and goes from there...you dont need any welding right just direct replacement?

aguilarf · 05-19-2008, 12:53 PM

Quote:

Originally Posted by acrod

how low is your car?

About 2 to 3 inches maybe in front. If you slide your foot under the cobar r lip, it will sit on top of your foot.

Usually have to use the factory scissor jack to get the sides high enough to roll my 3 ton craftsman floor jack underneath.

Plus I'm not a small guy, so I don't really feel like squeezing myself underthere.

aguilarf · 05-19-2008, 01:00 PM

Quote:

Originally Posted by 2k4mk1

Midas Mienke etc will not do it as it is against the law for them to remove any emissions control items. If yopu have ramps you could use about three pcs of 2x6 stacked progressively to raise the front so it would clear the ramps and be able to get it up on them. It is a little hard to explain online but hopefully you understand what I am saying

You mean ramps like these?

Mustangworld - Build yourself some ramps !

I would probably need to extend the first 2 steps due to the length of the lip.

Pic attached for visual reference.

aguilarf · 05-19-2008, 01:05 PM

Quote:

Originally Posted by FordGT08

i can install for cheaper than a shot just roll the fron tires on a 2x4 and then run my low profile jack under it and goes from there...you dont need any welding right just direct replacement?

Sorry for the multiple posts, not sure how to replay to several quotes in one message.

No welding direct swap out of factory H.

Also, Thanks ANR and Lethal for offering to do it.

FordGT08 · 05-19-2008, 02:23 PM

Quote:

Originally Posted by aguilarf

Sorry for the multiple posts, not sure how to replay to several quotes in one message.

No welding direct swap out of factory H.

Also, Thanks ANR and Lethal for offering to do it.

well if you want me to do it i can do it for cheaper

05-18-2008, 01:48 AM	#1
aguilarf 2001 Oxford White Mustang GT Join Date: Oct 2007 Location: San Antonio, TX Posts: 589 Trader Rating: (9)	Looking for exhaust shop to install OR H in NW side. Any know of a good exhaust shop on the NW side (Bandera/410, Culebra/410/1604) that would be willing to install an OR H pipe. I hit up some of the local franchise shops and the all declined. Car is too low to do it myself, so a lift would be the easiest way. Car is not a daily driver and probaly doesn't even see 500 miles per year. Thanks for your help. __________________ Last edited by aguilarf; 05-18-2008 at 02:21 AM.

05-18-2008, 02:08 AM	#2
Lethal Performance LSS Sponsor Join Date: Jun 2007 Location: SA,TX Posts: 361 Trader Rating: (1)	We could do it. If we can get lowered to the max Cobra's, Ford GT, Viper and Corvettes on the lift Im sure we can do yours. Email us at lethalperformance@yahoo.com __________________ www.lethalperformancesatx.com New website Dyno Tuning with: Hp tuners,SCT,Diablo and LT1 edit Email us at lethalperformance@yahoo.com. We will get back with you Open Tuesday thru Friday 9:00am to 6:30pm Saturday's by appointment only

05-18-2008, 10:20 AM	#5
2k4mk1 My name is ED,My mom calls me special,I dont know why? Join Date: Dec 2003 Location: SanAntonio Posts: 6,208 Trader Rating: (2)	Midas Mienke etc will not do it as it is against the law for them to remove any emissions control items. If yopu have ramps you could use about three pcs of 2x6 stacked progressively to raise the front so it would clear the ramps and be able to get it up on them. It is a little hard to explain online but hopefully you understand what I am saying __________________ 04 Oxford White MACH1,5 SPD with IUP,K&NAircharger Borla Stingers,SLP Catted X pipe,Tri-ax,SCT Flashtune,Max Mtr Spt 4 bolt adj C/C plates, Drilled/Slotted rotors all 4 corners 281 rwhp on Mustang Dyno,306 rwhp on a Dynojet 94 Black Lightning Daily Driver&85GT FACH1 Project under construction

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

05-18-2008, 09:41 AM	#3
acrod Registered User Join Date: May 2008 Location: san antonio,tx Posts: 46 Trader Rating: (0)	how low is your car?

05-18-2008, 09:44 AM	#4
H0SS302 Coming to a 17" rim near you Join Date: Jun 2007 Location: SA TOWN Posts: 6,183 Trader Rating: (6)	his car is pretty damn low, the front is like maybe 2inches off the ground(if that)

05-19-2008, 11:37 AM	#7
FordGT08 Registered User Join Date: Jan 2007 Location: San Antonio Posts: 1,239 Trader Rating: (0)	i can install for cheaper than a shot just roll the fron tires on a 2x4 and then run my low profile jack under it and goes from there...you dont need any welding right just direct replacement?